
PRODUCT DESCRIPTION
Crystal clear fast dual-component epoxy adhesive
FIELD OF APPLICATION
Suitable for fast, strong and invisible repair of many materials, such as pottery, porcelain, glass, leather, wood, stone, metal, ceramics. Both with themselves and in combination. Not suitable for Polyethylene (PE), polypropylene (PP), PTFE and silicone rubber.
PROPERTIES
PREPARATION
Working Conditions:
Recommended application at temperatures between +10°C and +35°C. Product cures by mixing the resin and hardener.
Personal safety:
Preferably wear gloves.
Surface Requirements:
The surface must be dry, clean and free of dust and grease.
Preliminary Surface Treatment:
Degrease parts to be bonded with denatured alcohol. Roughen smooth surfaces (sandpaper).
Tools:
Clean tools immediately after use with warm water and soap.
APPLICATION
Coverage:
1 ml = approx 10 cm² at a film thickness of 1 mm
Directions for use:
The surfaces to be bonded must be clean, dry and free from oil and grease. Smooth surfaces should be roughened. Break the nozzle and seal. Screw on enclosed mixer. Squeeze adhesive out of the syringe and apply to one side, to both sides with rough materials. Put parts together to fit exactly without pressure. Process time approximately 5 minutes at room temperature. The functional strength is reached after 20 min, final bonding strength after 12 h (both at room temperature). Unscrew and dispose mixer after use. Clean syringe nozzles and seal with cap. Use second mixer for next use. Store in upright position, in a cool, dry place. Do not use at temperatures below 10°C.
Stains/residue:
Remove wet stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.
Advice:
Some types of synthetics can not be joined such as polyethylene and polypropylene. Use a piece of adhesive tape in order to keep the parts in place while the adhesive is curing.
Points of attention:
After use close well (note: always place back the cap in the same way, due to the bonding of the cap to the double syringe). For optimum performance it is important to create a larger amount of adhesive and mix it very well. Curing time depends on the temperature. Adhesive does not cure below +5°C
TECHNICAL SPECIFICATIONS
| Bonding technique: | 1-Sided application |
| Chemical base: | Epoxy resin |
| Chemicals resistance: | e: Water, oil, grease, solvents, diluted acids and alkalis |
| Colour: | Transparent |
| Colour after curing/drying: | Transparent |
| Consistency: | Liquid |
| Density approx.: | 1,16 g/cm³ |
| Filling capacity: | Very good |
| Final bond strength (Alu): | 17 N/mm² |
| Final bond strength after: | 1 hour |
| Handling time: | 20 minutes |
| Minimum application temperature: | 5 °C |
| Minimum temperature resistance: | -40 °C |
| Maximum temperature resistance: | 100 °C |
| Moisture resistance: | Good |
| Mixture ratio: | 1:1 |
| Paintability: | Yes |
| Potlife: | 5 minutes |
| Solvent free: | Yes |
| UV resistance: | Good |
| Viscosity: | Medium viscosity |
| Viscosity approx.: | 20000 mPa·s |
| Water resistance: | Good |
| soluble: | No |
STORAGE CONDITIONS
Store in tightly closed packaging in a dry, cool and frost-free place.
| Código de producto | 37545 |
| Fabricante | UHU |
| Condition | New |
PRODUCT DESCRIPTION
Crystal clear fast dual-component epoxy adhesive
FIELD OF APPLICATION
Suitable for fast, strong and invisible repair of many materials, such as pottery, porcelain, glass, leather, wood, stone, metal, ceramics. Both with themselves and in combination. Not suitable for Polyethylene (PE), polypropylene (PP), PTFE and silicone rubber.
PROPERTIES
PREPARATION
Working Conditions:
Recommended application at temperatures between +10°C and +35°C. Product cures by mixing the resin and hardener.
Personal safety:
Preferably wear gloves.
Surface Requirements:
The surface must be dry, clean and free of dust and grease.
Preliminary Surface Treatment:
Degrease parts to be bonded with denatured alcohol. Roughen smooth surfaces (sandpaper).
Tools:
Clean tools immediately after use with warm water and soap.
APPLICATION
Coverage:
1 ml = approx 10 cm² at a film thickness of 1 mm
Directions for use:
The surfaces to be bonded must be clean, dry and free from oil and grease. Smooth surfaces should be roughened. Break the nozzle and seal. Screw on enclosed mixer. Squeeze adhesive out of the syringe and apply to one side, to both sides with rough materials. Put parts together to fit exactly without pressure. Process time approximately 5 minutes at room temperature. The functional strength is reached after 20 min, final bonding strength after 12 h (both at room temperature). Unscrew and dispose mixer after use. Clean syringe nozzles and seal with cap. Use second mixer for next use. Store in upright position, in a cool, dry place. Do not use at temperatures below 10°C.
Stains/residue:
Remove wet stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically.
Advice:
Some types of synthetics can not be joined such as polyethylene and polypropylene. Use a piece of adhesive tape in order to keep the parts in place while the adhesive is curing.
Points of attention:
After use close well (note: always place back the cap in the same way, due to the bonding of the cap to the double syringe). For optimum performance it is important to create a larger amount of adhesive and mix it very well. Curing time depends on the temperature. Adhesive does not cure below +5°C
TECHNICAL SPECIFICATIONS
| Bonding technique: | 1-Sided application |
| Chemical base: | Epoxy resin |
| Chemicals resistance: | e: Water, oil, grease, solvents, diluted acids and alkalis |
| Colour: | Transparent |
| Colour after curing/drying: | Transparent |
| Consistency: | Liquid |
| Density approx.: | 1,16 g/cm³ |
| Filling capacity: | Very good |
| Final bond strength (Alu): | 17 N/mm² |
| Final bond strength after: | 1 hour |
| Handling time: | 20 minutes |
| Minimum application temperature: | 5 °C |
| Minimum temperature resistance: | -40 °C |
| Maximum temperature resistance: | 100 °C |
| Moisture resistance: | Good |
| Mixture ratio: | 1:1 |
| Paintability: | Yes |
| Potlife: | 5 minutes |
| Solvent free: | Yes |
| UV resistance: | Good |
| Viscosity: | Medium viscosity |
| Viscosity approx.: | 20000 mPa·s |
| Water resistance: | Good |
| soluble: | No |
STORAGE CONDITIONS
Store in tightly closed packaging in a dry, cool and frost-free place.
| Código de producto | 37545 |
| Fabricante | UHU |
| Condition | New |
©2023 - 2025 rosamarcr.com - Todos los derechos reservados.
Todo el contenido de este sitio cuenta con derechos registrados, se permite el uso de imágenes y textos solamente mediante la autorización expresa.